最新的000-104题库下载！（killtest题库网提供）

IBM认证 000-104考试题库由我们专业IT认证讲师及产品专家精心打造，包括了当前最新的全真试题，全部附有正确答案。

在IBM认证厂商对考试做出变动后，网站都将在第一时间公布题库的更新情况。确保题库覆盖率始终在96%以上，最终能够使考生一次通过考试，同时killtest题库网承诺“一次不过，全额退款”保证了考生的利益不受到任何的损失！

1. A backup is taken using the following command:
tar -cvf abcdef.tar /usr/local/include/tcpd.h
The operator is in the directory /usr/local/restores and runs the following command:
tar -xvf abcdef.tar
Where will the file be restored?
A./usr/local/include/tcpd.h
B./usr/local/restores/tcpd.h
C./usr/local/restores/include/tcpd.h
D./usr/local/restores/usr/local/include/tcpd.h
Answer: A
2. An administrator is applying a corrective service to their HMC. The corrective service has been
shipped on 3 DVDs. Which action will ensure the corrective service is correctly installed?
A.Select the option to automatically reboot the HMC.
The safer , easier way to help you pass any IT exams.
6 / 7
B.Select the option to automatically reboot the HMC after each disk.
C.Shutdown all managed LPARs prior to beginning the install process.
D.Copy all disks into the ""SERVICE"" directory and select concurrent install.
Answer: A
3. A POWER6 595 LPAR has two dedicated processors. The LPAR is active and running AIX 6.1. What
must be done to donate any unused processing capacity to the shared processor pool?
A.In the HMC Properties, select the options to allow processor sharing when the partition is inactive and
active.
B.In the LPAR Properties, select the options to allow processor sharing when the partition is inactive and
active.
C.In the LPAR Profile Properties, select the options to allow processor sharing when the partition is
inactive and active.
D.In the 595 Managed System Properties, select the options to allow processor sharing when partitions
are inactive and active.
Answer: C
4. The administrator changed the number of virtual processors from 1 to 2 in the default_profile of an
LPAR. The operator ran the cfgmgr command expecting to see 2 processors after that, but did not see
them.
What action must be done to apply the changes?
A.Reboot AIX within the LPAR.
B.Run cfgmgr against the device sys0.
C.Shutdown and then activate the default_profile.
D.Ensure the RSCT daemon is operative and run cfgmgr again.
Answer: C
5. An administrator needs to recover an HMC due to a failed disk. The disk has been replaced, allowing
the administrator to reinstall the HMC back to the required release of software. Backups of both the HMC
Console Data and Upgrade Data are available.
After reloading the HMC with the Recovery DVDs, what are the next steps to restore the HMC
configuration?
A.Use the 'HMC Management > Restore HMC Data' option to first restore just the HMC Data..
B.Use the 'HMC Management > Restore Upgrade Data' option to first restore just the Upgrade Data.
C.Use the 'HMC Management > Restore HMC Data' option to first restore the HMC Data and then the
Upgrade Data.
D.Use the 'HMC Management > Restore Upgrade Data' option to first restore the Upgrade Data, and then
the HMC Data.
Answer: A
6. An administrator is looking for the "Open Restricted Shell Terminal" option on the HMC GUI. Under
which panel is this option available?
A.HMC Management, but only from a local connection
B.Service Management, but only from a local connection.
C.Systems Management, but only from a local connection.
D.Systems Management, but only from a remote connection.
Answer: A